Yes. You can go up or down one gauge, usually without needing to readjust your truss rod, however if you use a much heavier or lighter gauge this will put different amounts of tension on the neck so an adjustment may be needed. When changing string gauge allow some time for the guitar to settle and then if needed have the truss rod adjusted by a qualified technician.
No. Putting Steel strings on a Nylon string guitar can add extra stress to the guitar top and may cause the bridge to lift. These guitars are braced differently and steel and nylon strings are not interchangeable.
Do not use any wax based products on the guitar, especially on the top! This will cause unwanted wax buildup over time which will impede the top from vibrating. Instead use a small amount of soap based guitar polish sprayed on a cloth (never directly on the guitar) and gently wipe off your guitar. For the fingerboard we suggest removing the strings and applying Lemon or Danish oil to a cloth and then working it into your fingerboard. Let the oil soak in for a few minutes and then wipe off the excess. This should be done once a year on rosewood or ebony fingerboards only. Doing so not only cleans, but conditions your fingerboard against cracking and keeps it from losing its luster.
Since our factories are located in different parts of Quebec, a complete tour would entail about one thousand kilometers of driving and at least a complete weekend. We are hoping to offer tours in the future but at this point we haven't worked out the logistics.
Cedar tends to produce a warmer sound and ages faster than spruce. Spruce is brighter and ages more over a longer period of time. Visually, cedar is darker in color with a fairly tight grain pattern. Spruce tends to be very blond with a slightly wider grain pattern.
A truss rod is an adjustable metal rod that sits inside of the neck, underneath the fingerboard. The truss rod is used to adjust for changes in the neck caused by humidity or changing string gauges. Seagull guitars employ an advanced double function truss system.
This is not nearly as big a problem as some people make it out to be. Once again the culprit here is humidity. In the case of the protruding fret edges this is because the fingerboard has dried out slightly and shrunk. The frets are metal (nickel/silver) and do not shrink from a change in humidity. The problem is easily fixed by a good guitar tech with a file.
Yes. It is a good idea to loosen the strings just enough to reduce tension on the neck. This will avoid extra stress which can cause damage to the headstock if the guitar case is dropped.
We recently came across a disposable plastic lighter that was being promoted as a “Limited Edition”. Likewise we find ourselves surrounded by products that are touted as being “handmade” and when it comes to guitars you’ll have a tough time finding one that isn’t described as handmade. Our dictionary defines handmade simply as: “made by hand, not machinery”. If you accept that definition then it’s safe to say there is no such thing as a handmade guitar! In any case our recommendation would be to forget the whole “handmade” thing and focus on more relevant considerations such as: finish material, type of wood used (and whether it is genuine), and most importantly how does it feel and sound to you.
Cold-checking refers to that spider web like effect that sometimes occurs in wood finishes that have been subjected to severe temperature changes. It is also common in older instruments where the finish has dried out to the point of becoming brittle. For many years we have worked with our finish supplier to develop a lacquer formula that retains a degree of elasticity and resists cold checking.
Your truss rod should be adjusted when your neck develops a bit of a bow in it. The reason for the bow is a combination of the string tension that is constantly applied to the neck along with changes in relative humidity. Humidity is the most important part of this equation. Wood reacts to changes in relative humidity when it absorbs or loses moisture. Absorbing moisture causes the neck to expand which results in a back-bow in this case loosening the truss rod slightly will allow the neck to return to its original form. When a neck dries out it will under bow, which can be treated by slightly tightening the truss rod (Click here for a pdf diagram).
Warning: Over adjusting your truss rod can cause irreparable damage to your guitar and therefore truss rod adjustments should only be handled by a qualified guitar technician.
Godin strings are recommended as they are made specifically for our acoustic brands including Seagull. Designed by Robert Godin and the leading American string manufacturer, our strings come in three sizes of high quality phosphor bronze. Seagull guitars are fitted with A6 Lite strings and these are recommended for continued use, but Medium and Extra Lite are also available to fit your desired tone and functionality.